Accessories for blowing-in, calibration
Cable avoidance and transmitter locating system
Current laying techniques also include direct blow-in methods, for which the cable ducts have to be gauged beforehand to check them for any internal deformations. This will ensure unhampered blow-in. The gauge, which contains a sonde, is blown through the cable duct by compressed air. If the gauge with the sonde gets stuck in transit, its position can exactly be pinpointed down to a depth of 4.50 m by passing a receiver along the course of the cable duct. As soon as the receiver approaches the sonde, a continuous optical and acoustic signal will be emitted, which will reach its maximum level right on top of the underground location where the sonde has to stuck.
The additionally applications are the localization of underground laid cables, metal lines and house service lines. Lines can be irradiated with the transmitter that the signal will be strong enough for the receiver.
Diameter: 18 mm
Order No. 009.674.10
including 2 pulling grips and an anti-twist swivel
Ø 35 mm, 5 pipes on laid cable 10-16 mm
Order No. 111.491.00
Easy location of pipe damages
Range: 2-3 m
Scope of delivery: 1 Sonde, 2 Batteries, Storage Box
Order No. 009.675.61
Order No. 009.675.62
Order No. 009.675.63
made of galvanized steel wire, one thimble, double, reduced to single
Order No. 117.053.00
for pipe inner Ø 32-60 mm
Order No. 126.800.00
for sleeved pistons and measuring gauge with sonde
Weight: 2.5 kg
Order No. 111.041.00
The plug is equipped with a o-ring for 100% sealing. It is easy to mount with self cutting thread. It is available in other sizes. Please specify when ordering.
Weight: 3.1 kg
Order No. 111.042.00
End sizing installation similar 111.042.00, with connection to pressure gauge with logging (not illustrated)
Order No. 111.042.01
Fitting for 10 mm pipes (not illustrated)
Order No. 111.042.02
for leak test, could be connected to the end sizing installation
It nebulises the lubricant whereas the amount is adjustable. Alternatively the airflow could be bypassed. The lubricator is suitable for any micro pipe.
Order No.: 111.450.00
for blowing cable in compressed air pipes of already installed copper cables of the German Telekom. An additional amount of air could be brought via the compressed air pipes into the copper cable.
Order No.: 111.451.00
Order No. 111.261.50
For lengthwise and crosswise cuts
Order No. 111.444.00
To blow in a second cable or micro pipe, the Y-Fitting joins the old pipe with an intermediate pipe which is connected with the Powerflow. The protective pipe gets locked on both sides.
Order No. 111.242.10 with insertions for 32, 40, 50 mm pipe
Order No. 111.242.20 for 63 mm pipe
Adapter and sealings could be used of the blowing junction block o the blowing machine. Please order if not available.
for Powerflow and Multiflow. This pump enables a precise dosing for constant lubrication and increases the to be laid length a lot. (Without can of cable slip oil)
Order No. 111.244.00
to connect flush mounted pipes in ducts for blowing-in cabel / Pipe up to dia. max. 25 mm
Order No. 111.500.00
With the loops can be reduced down to approx. 70 mm. This rest could be carefully inserted into the micro pipe and the pipe ends connected with a bushing.
If it is not possible to insert the whole length in one step, the cable drum has to be positioned in the middle of the trail. The first length gets inserted in one direction and the remaining cable laid into the cage.
The uncoiling cages all owes a controlled and efficient uncoiling of the cable off the drum. The large version is dismountable for transport.
Uncoiling cage large
Uncoiling cage small
Laterally of the drum is the inner end of the duct where this unit is to be inserted and remain fixed during the injection procedure. A pressure loss will become visible at the manometer immediately.
Order No. 111.261.00
facilitates this procedure and shortens the temporal expenditure to a minimum. A pressure loss will become visible at the manometer immediately. (The connecting hoses to 111.261.00 are included)
Order No. 111.260.00
The guidance unit is to be positioned between the micro duct drums and the Multiflow. It ensures a regular uncoiling of the ducts..
Order No. 111.262.00
This acceptance fits in all trailers of the series BKT 18 up to BKT 27
Order No. 028.328.02
hinged and galvenized
Each strand has a tensile load of max. 300 kg.
Attention: Please follow the tensile load limit restrictions of the appropriate micro pipe.
The single strands are to be assembled, please make your choice.
Shekel for pulling unit needs to be ordered seperately
Order No. 107.070.00